Siemens CERBERUS PYROTRONICS PXL Скачать руководство пользователя страница 59

Страница: 59 / 83

Testing and Troubleshooting

PXL Conventional Fire Alarm Control Panel

5 TESTING AND TROUBLESHOOTING

WALK TEST

Important

Inform the person in charge of the PXL fire alarm system that a

Walk Test is to be performed and that part or all of the fire detec-

tion system will be disabled. It is also advisable (or may be

required) to notify the fire department of the test.

Use the Walk Test feature to test the entire fire alarm system in

either of the following two ways:
1. When an initiating device is activated, the system notification

appliances sound steady and the appropriate zone LED turns on

for 2 seconds.

2. When an initiating device is activated, only the appropriate zone

LED turns on for 2 seconds. Notification appliances are not

turned on.

Note:

Devices tested on supervisory zones will annunciate

twice. The first time is when the device is moved to the

off-normal state. The second time is when the device is

restored to normal.

The PXL automatically exits the Walk Test mode if there is no activity

on the system for 20 minutes.

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Содержание CERBERUS PYROTRONICS PXL




















































































Результаты поиска

Содержание CERBERUS PYROTRONICS PXL

Отзывы:

Похожие инструкции для CERBERUS PYROTRONICS PXL

Бренды по названию

Популярные бренды

Siemens CERBERUS PYROTRONICS PXL, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CERBERUS PYROTRONICS PXL

Отзывы:

Похожие инструкции для CERBERUS PYROTRONICS PXL

Бренды по названию

Популярные бренды