Siemens Cerberus PRO FC721 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 118

background image

Connectivity and communication with 'Station'
Setting Windows firewall

9

74 | 118
Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

9 Connectivity and communication with 'Station'

A PC does not have to be directly connected to a ↑ 'Station' to be able to

communicate with a 'Station' in the ↑ 'Site'. The PC can be connected to any place

in the Ethernet.
Detailed information about the connection variants can be found in the

'Establishing connection from PC to FS720 network' chapter in document

A6V10210424. See chapter 'Applicable documents'.

9.1 Setting Windows firewall

● The Windows firewall may prevent the PC connecting to the ↑ 'Station'.
● A functioning Ethernet connection between the Cerberus-Engineering-Tool on

the PC and the FS720 control panels is required to update the firmware, for

example.

Setting Windows firewall

● Create a firewall rule for Windows. To do this, proceed as follows:

You must have administrator rights to make the following settings.

9.1.1 Windows XP

ϖ

You have administrator rights on your PC

1. Open the Windows start menu.
2. Select 'Settings' > 'Control panel' > 'Administrative Tools' > 'Services'.
3. Right-click on 'Windows Firewall/Internet Connection Sharing (ICS)' in the new

window.

4. Select 'All Tasks' > 'Exit' in the context menu.
5. Once the work is complete, reactivate the firewall. To do this, proceed as

described above but select 'All Tasks' > 'Start' in the context menu.

NOTICE

Security vulnerability in operating system due to deactivated firewall
Unauthorized access to your PC
● Activate the firewall after the firmware update.

«
...
72
73
74
75
76
...
»

Содержание Cerberus PRO FC721























































































































Отзывы:

Нет отзывов

Похожие инструкции для Cerberus PRO FC721

Smart-MPPT Li Series

Бренд: Y-Solar Страницы: 6

Бренд: NEC Страницы: 149

Бренд: NEC Страницы: 13

C-NaviGator III

Бренд: C-Nav Страницы: 20

Бренд: Galaxy Control Systems Страницы: 5

Бренд: Parker Страницы: 12

Бренд: Parkside Страницы: 65

Бренд: Samson Страницы: 6

ArtNet-DMX Mux16

Бренд: DMX4ALL Страницы: 21

Бренд: Fancom Страницы: 23

Бренд: Beninca Страницы: 7

ZITON RADIO LOOP MODULE

Бренд: EMS Страницы: 26

Бренд: Danfoss Страницы: 30

Бренд: DeLaval Страницы: 102

Бренд: Pfeiffer Vacuum Страницы: 100

SUPERSEAL 2014 Series

Бренд: APV Страницы: 20

Бренд: LEYBOLD Страницы: 12

Бренд: Hach Страницы: 504

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды