Siemens Cerberus PRO FC721 Скачать руководство пользователя страница 39

Страница: 39 / 118

Mounting

Options

39 | 118

Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

5.5.4 Cable kit (communication)

The cable kit (communication) FCA2014-A1 is used as an intermediate piece for

wiring the external lines to the modules on the operating unit. The connecting

cables supplied are fully assembled and have a length of 1110 mm. The cable kit is

mounted in the top right of the housing instead of the shield connection terminal

blocks.

Figure 13: Installation of the cable kit (communication) on the rear panel (example, Standard housing)

1 Screw bushings in rear panel for terminal strip
2

Terminal strip with 2 shield connection terminal blocks and connection

terminals

3 2x fixing screws
4 Periphery board

Mounting steps

1. First remove the shield connection terminal blocks if present.
2. Screw the mounting rail (2) to the screw bushings in the rear panel (1) using

the two fixing screws (3).

3. Now wire the existing module to the operating unit using the cables provided

according to the allocation plan of the respective module.

4. Guide the cable to the operating unit along the rear panel and fasten using

cable ties.

Содержание Cerberus PRO FC721























































































































Результаты поиска

Содержание Cerberus PRO FC721

Отзывы:

Похожие инструкции для Cerberus PRO FC721

Бренды по названию

Популярные бренды

Siemens Cerberus PRO FC721, Техническое руководство

Результаты поиска

Содержание Cerberus PRO FC721

Отзывы:

Похожие инструкции для Cerberus PRO FC721

Бренды по названию

Популярные бренды