Siemens AXIOM Iconos R200 Скачать руководство пользователя страница 60

Страница: 60 / 238

System Operation

On-Off/Emergency Stop

/ 32

AXD3-340.620.13.01.02

Operator Manual

Switching back on

◆

Remove the hazardous situation.

◆

Unlock the red emergency stop button
– The system is immediately ready for use

◆

If the hazardous situation cannot be removed, please notify the Siemens Cus-
tomer Service.

Patient rescue

If the patient has to be rescued in an emergency situation (e.g. power failure),
proceed as follows:

◆

Bring accessories into a position which makes rescue possible.

If the patient is compressed with the cone (optional)

◆

Pull out the knob (1) from the engaged position b and turn it by 90° until it en-
gages in the deep notch (notch position a).

◆

Lift the cone arm off from the patient until it locks in a position of approx. 10°.

(1)

Warning

If shoulder supports or foot restraints are loosened in Trendelenburg position,
then take care that the operating personnel secure the patient sufficiently.
Obtain the assistance of sufficient personnel for the rescue of the patient.

Содержание AXIOM Iconos R200















































































































































































































































Результаты поиска

Содержание AXIOM Iconos R200

Отзывы:

Siemens AXIOM Iconos R200, Руководство оператора, Страница: 60 / 238

Результаты поиска

Содержание AXIOM Iconos R200

Отзывы: