manualshive.com logo in svg

Siemens ASIC SIM 1-2, Руководство по эксплуатации функций

Поделиться
Скачать
Siemens ASIC SIM 1-2 Скачать руководство пользователя страница 9

 

SIM 1-2 
C79000-G8976-C215-01 

9

 

 

Area of Application and Characteristics 

1

1.1 Overview 

Examples of applications for the SIM 1-2 

The SIM 1-2 (

S

iemens 

I

EC 

M

AU) allows the setting up of a fieldbus 

M

edium 

A

ttachment 

U

nit (MAU) for 31.25 Kbps complying with IEC 61158-2 regardless of 

the implemented data link layer protocol.  

In conjunction with a suitable communication controller, for example, SPC 4-2, 
devices with a fieldbus attachment can be implemented with little effort. 

The SIM 1-2 supports all send and receive functions (including jabber control) and 
the high-impedance decoupling of auxiliary energy from the bus cable.  

It provides a selectable, stabilized power supply and also allows the setup of an 
galvanically isolating power supply with a few passive components.  

As an alternative to the standard signal interface  (TxS, TxE, RxS, RxA), the ASIC 
includes special interface logic that provides low power consumption and an easy-
to- implement interface for galvanic signal isolation.  

Содержание ASIC SIM 1-2































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды