Siemens ASIC SIM 1-2 Скачать руководство пользователя страница 18

Страница: 18 / 62

Functional Description of the SIM 1-2

SIM 1-2

C79000-G8976-C215-01

2.3.4 Bus

Connector

Bus Current Consumption

Using the resistor R

RISOLL

, the mean current taken from the bus is set from 2

. In the range from 2 mA to 10 mA, the SIM 1-2 automatically operates in

the asymmetric modulation mode. This means that to transmit, the mean current
consumption is raised to 10

and then lowered again to the set value.

The set mean bus current must always be at least 1 mA higher than the current
transferred to the application over VREG and VE (including DC/DC).

RISOLL

Ω

] = 0.05 * I

BUS

[mA]

Conditions for R

RISOLL

: 100

Ω

≤

RISOLL

≤

2.5 M

Ω

the capacitor C

must be dimensioned in the permitted range according to the

pulse load by the application or the DC/DC converter.

Caution 1

To achieve the minimum bus current tolerance of 3 %, resistors with a tolerance of

≤

0.1 % must be used. As an alternative, the bus current can be matched over

RISOLL

(see also tolerance calculation in section 2.3.7, "Reference Circuit RIREF,

RVCCVE, RVREG, RISOLL“).

Caution 2

Transistor T1 and its cooling surface must be designed according to the set bus
current consumption and the resulting dissipation loss.

Содержание ASIC SIM 1-2































































Результаты поиска

Содержание ASIC SIM 1-2

Отзывы:

Бренды по названию

Популярные бренды

Siemens ASIC SIM 1-2, Руководство по эксплуатации функций

Результаты поиска

Содержание ASIC SIM 1-2

Отзывы:

Бренды по названию

Популярные бренды