Siemens ASIC SIM 1-2 Скачать руководство пользователя страница 11

Страница: 11 / 62

Area of Application and Characteristics

SIM 1-2
C79000-G8976-C215-01

1.2 Essential

Characteristics

Description

The essential characteristics of the SIM 1-2 (IEC MAU) are listed below.

Characteristics of fieldbus attachment

Using the SIM 1-2, a fieldbus attachment can be implemented with the following
characteristics.

●

The SIM 1-2 (IEC MAU) supports fieldbus attachments for 31.25 Kbps in

compliance with IEC 6 1158-2.

●

The SIM 1-2 can be connected to all Manchester encoders/decoders in

compliance with IEC 61158-2.
As a result, the SIM 1-2 can also be connected to all fieldbus controllers that
already include a Manchester encoder/decoder in compliance with
IEC 61158 2.

●

Jabber inhibit (jabber control prevents a node from transmitting indefinitely on

the bus)

●

Sender with current modulator for bias currents:

–

Asymmetric modulation from 2 mA to 10 mA

–

Symmetric modulation from 10 to 50 mA

Power-optimized electrical isolation

The SIM 1-2 supports simple and power-minimized galvanic isolation between
MAU and user electronics by means of:

●

Integrated voltage converter for power-optimized, unregulated voltage

transformation; external transformer and rectifier are required.

●

Integrated interface logic for simple and current-saving galvanic signal

isolation, current consumption in permanent operation < 2 mA; 2 optocouplers
and suitable controller interface logic are necessary on the controller.

Содержание ASIC SIM 1-2































































Результаты поиска

Содержание ASIC SIM 1-2

Отзывы:

Бренды по названию

Популярные бренды

Siemens ASIC SIM 1-2, Руководство по эксплуатации функций

Результаты поиска

Содержание ASIC SIM 1-2

Отзывы:

Бренды по названию

Популярные бренды