Siemens 7SR10 Argus Series страница 273 Скачать руководство пользователя | Manualshive

Страница: 273 / 286

background image

7SR10, 7SR11, 7SR12 Applications Guide

© 2018 Siemens Protection Devices Limited

Chapter 7 Page 29 of 41

Section 4: Control Functions

4.1 Auto-reclose Applications

•

Automatic circuit reclosing is extensively applied to overhead line circuits where a high percentage of faults

that occur are of a transient nature. By automatically reclosing the circuit-breaker the feature attempts to

minimise the loss of supply to the customer and reduce the need for manual intervention.

The function supports up to 4 ARC sequences. That is, 4 x Trip / Recloses followed by a Trip & Lockout. A lockout

condition prevents any further automatic attempts to close the circuit-breaker. The number of sequences selected

depends upon the type of faults expected. If there are a sufficient percentage of semi-permanent faults which

could be burnt away, e.g. fallen branches, a multi shot scheme would be appropriate. Alternatively, if there is a

high likelihood of permanent faults, a single shot scheme would minimise the chances of causing damage by

reclosing onto a fault. In general, 80% of faults will be cleared by a single Trip and Reclose sequence. A further

10% will be cleared by a second Trip and Reclose. Different sequences can be selected for different fault types

(Phase/Earth/Sensitive Earth faults).
The Deadtime is the interval between the trip and the CB close pulse being issued. This is to allow for the line to

go ‘dead’ after the fault is cleared. The delay chosen is a compromise between the need to return the line to

service as soon as possible and prevented unnecessary trips through re-closing too soon. The Reclaim Time is

the delay following a re-closure before the line can be considered back in service. This should be set long enough

to allow for protection operation for the same fault, but not so long that two separate faults could occur in the

same Autoreclose (ARC) sequence and cause unnecessary lockouts.
The Sequence Fail Timer provides an overall maximum time limit on the ARC operation. It should therefore be

longer than all the set delays in a complete cycle of ARC sequences; trip delays, Deadtimes, Reclaim Time etc.

Generally this will only be exceeded if the circuit-breaker has either failed to open or close.
Since large fault currents could potentially damage the system during a prolonged ARC sequence, there are also

settings to identify which protection elements are High-sets and these can cause an early termination of the

sequence.
Where a relay is to operate as part of an ARC scheme involving a number of other relays, the feature attempts to

clear any faults quickly without regard to normal fault current grading. It does this by setting each Trip element to

be either Delayed or Instantaneous. Instantaneous Trips are set to operate at just above maximum load current

with small delays while Delayed Trips are set to suit actual fault levels and with delays suitable for current

grading.
A typical sequence would be 2 Instantaneous Trips followed by a Delayed Trip & Lockout:

•

When any fault occurs, the relay will trip instantaneously and then reclose.

•

If this does not clear the fault, the relay will do the same again.

•

If this still does not clear the fault, the fault is presumed to be permanent and the next Trip will be

Delayed and so suitable for grading with the rest of the network. Thus allowing downstream

protection time to operate.

•

The next trip will Lockout the ARC sequence and prevent further recloses.

It is important that all the relays in an ARC scheme shadow this process – advancing through their own ARC

sequences when a fault is detected by an element pickup even though they are not actually causing a trip or

reclose. This is termed Sequence Co-ordination and prevents an excessive number of recloses as each

successive relay attempts to clear the fault in isolation. For this reason each relay in an ARC scheme must be set

with identical Instantaneous and Delayed sequence of trips.

Figure 4-1 Sequence Co-ordination

B

A

D

C

«
...
271
272
273
274
275
...
»

Содержание 7SR10 Argus Series































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7SR10 Argus Series

Бренд: Energenie Страницы: 2

Бренд: Sel Страницы: 24

Бренд: Sel Страницы: 370

Бренд: ABB Страницы: 40

Бренд: National Instruments Страницы: 65

Бренд: Allen-Bradley Страницы: 2

SIRIUS 3UG4616-1BR28-0AA1

Бренд: Siemens Страницы: 6

Бренд: Veris Industries Страницы: 2

SLV CONTROL 470806

Бренд: SLV Страницы: 34

CCE-3000 Series

Бренд: KMC Controls Страницы: 2

Relay Coach BLE

Бренд: Freelap Страницы: 2

Бренд: ehb electronics Страницы: 10

Бренд: ETC Страницы: 5

Бренд: ETC Страницы: 8

Бренд: DMX4ALL Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды