Siemens 7ML5430 Скачать руководство пользователя страница 96

Страница: 96 / 111

Application examples

C.3 Example 2: Horizontal vessel with volume measurement

SITRANS Probe LR with mA/HART

Operating Instructions, 05/2019, A5E32337711-AC

C.3

Example 2: Horizontal vessel with volume measurement

Note

•

The minimum distance from the flange face to the target is limited by Near Blanking

P800.

•

Only set P837 if the product is at least 2 m (78”) away from the flange face. If it is closer,

leave P837 at 1 until the level drops and the distance increases beyond 2 m (78”).

The application is to obtain a level measurement and corresponding 4 to 20 mA output

proportional to vessel volume in a chemical vessel. Process empty level (Empty) is the

bottom of the tank, which is 3.5 m from the antenna flange face. Process full level (Span) is

3.0 m from the vessel bottom. The maximum rate of filling or emptying is about 0.2 m/min.

Selecting tank shape 7 at P050, and entering values for A and L, will give a volume reading

instead of level. In the event of a loss of echo, SITRANS Probe LR is to go into Failsafe Hi

after 2 minutes.

①

Empty

②

Reference point

③

Volume reading

Parameter

Description

Value

Function

P001

Mode of measurement

Volume replaces Level when a tank shape

is selected at P050

P003

Measurement response 2

1 m/minute

P005

Units

meters

P006

Empty distance

3.5

3.5 m

P007

Span

3 m

P050

Vessel shape

parabolic ends

P051

Maximum volume

8000

8000 liters

P052

Vessel dimension A

0.8

0.8 meters

P053

Vessel dimension L

6 meters

P070

Failsafe timer

2 minutes

P071

Failsafe

Содержание 7ML5430
















































































































Результаты поиска

Содержание 7ML5430

Отзывы:

Siemens 7ML5430, Руководство по эксплуатации, Страница: 96 / 111

Результаты поиска

Содержание 7ML5430

Отзывы: