Siemens 7ML5430 Скачать руководство пользователя страница 8

Страница: 8 / 111

SITRANS Probe LR with mA/HART

Operating Instructions, 05/2019, A5E32337711-AC

Introduction

1.1

Purpose of this documentation

These instructions contain all information required to commission and use the device. Read

the instructions carefully prior to installation and commissioning. In order to use the device

correctly, first review its principle of operation.
The instructions are aimed at persons mechanically installing the device, connecting it

electronically, configuring the parameters and commissioning it, as well as service and

maintenance engineers.

1.2

Checking the consignment

Check the packaging and the delivered items for visible damages.

Report any claims for damages immediately to the shipping company.

Retain damaged parts for clarification.

Check the scope of delivery by comparing your order to the shipping documents for

correctness and completeness.

WARNING

Using a damaged or incomplete device
Risk of explosion in hazardous areas.

•

Do not use damaged or incomplete devices.

1.3

Industrial use

NOTICE
Use in a domestic environment
This Class B Group 1 equipment is intended for use in industrial areas.
In a domestic environment this device may cause radio interference.

Содержание 7ML5430
















































































































Результаты поиска

Содержание 7ML5430

Отзывы:

Siemens 7ML5430, Руководство по эксплуатации, Страница: 8 / 111

Результаты поиска

Содержание 7ML5430

Отзывы: