Siemens 7ML5430 Скачать руководство пользователя страница 74

Страница: 74 / 111

SITRANS Probe LR with mA/HART

Operating Instructions, 05/2019, A5E32337711-AC

Troubleshooting

9.1

General fault codes

Note

•

The General Fault Codes were revised with Firmware Revision 3.02. If your device has

earlier firmware, see Fault codes (firmware revision 1.05 or earlier) (Page 76).

•

Some faults cause the device to go to Failsafe mode (Fault 52). These are indicated with

an asterisk (*).

9.2

Fault codes (firmware revision 3.02 or higher)

Note
Some faults cause the device to go to Failsafe mode (Fault 34). These are indicated with an

asterisk (*).

Code

Meaning

Corrective action

S:0

* The device was unable to get a measurement

within the Failsafe Timer period. Possible caus-

es: faulty installation, antenna buildup, foam-

ing/other adverse process conditions, invalid

calibration range.

Ensure installation details are correct.

Ensure no antenna buildup. Adjust pro-

cess conditions to minimize foam or

other adverse conditions. Correct range

calibration. If fault persists, contact your

local Siemens representative.

S:2

* The device is operating in a low power condition

that is outside its operating range. As a result, a

valid measurement has not been taken for the

failsafe timer period, and the device will be put

into failsafe mode.

Correct the power supply (resistance or

voltage).

S:3

Device is nearing its lifetime limit according to

the value set in Maintenance Required Limit.

Replacement is recommended.

S:4

Device is nearing its lifetime limit according to

the value set in Maintenance Demanded Limit.

Replacement is recommended.

S:6

Sensor is nearing its lifetime limit according to

the value set in Maintenance Required Limit.

Replacement is recommended.

S:7

Sensor is nearing its lifetime limit according to

the value set in Maintenance Demanded Limit.

Replacement is recommended.

S:8

Service interval as defined in Maintenance Re-

quired Limit has expired.

Perform service.

S:9

Service interval as defined in Maintenance De-

manded Limit has expired.

Perform service.

S:11 Internal temperature sensor failure.

Repair required: contact your local Sie-

mens representative.

Содержание 7ML5430
















































































































Результаты поиска

Содержание 7ML5430

Отзывы:

Siemens 7ML5430, Руководство по эксплуатации, Страница: 74 / 111

Результаты поиска

Содержание 7ML5430

Отзывы: