Siemens 7ML5430 Скачать руководство пользователя страница 72

Страница: 72 / 111

SITRANS Probe LR with mA/HART

Operating Instructions, 05/2019, A5E32337711-AC

Service and maintenance

WARNING

Impermissible repair and maintenance of the device

•

Repair and maintenance must be carried out by Siemens authorized personnel only.

8.1

Maintenance and repair work

SITRANS Probe LR requires no maintenance or cleaning under normal operating conditions.
Under severe operating conditions, the antenna may require periodic cleaning. If cleaning

becomes necessary:

●

Note the antenna material and the process medium, and select a cleaning solution that

will not react adversely with either.

●

Remove the instrument from service and wipe the antenna clean using a cloth and

suitable cleaning solution.

8.2

Return procedure

Enclose the bill of lading, return document and decontamination certificate in a clear plastic

pouch and attach it firmly to the outside of the packaging.

Содержание 7ML5430
















































































































Результаты поиска

Содержание 7ML5430

Отзывы:

Siemens 7ML5430, Руководство по эксплуатации, Страница: 72 / 111

Результаты поиска

Содержание 7ML5430

Отзывы: