Siemens 7ML5430 Скачать руководство пользователя страница 26

Страница: 26 / 111

SITRANS Probe LR with mA/HART

Operating Instructions, 05/2019, A5E32337711-AC

Commissioning

6.1

Basic safety notes

WARNING

Loss of explosion protection
Risk of explosion in hazardous areas if the device is open or not properly closed.

•

Close the device as described in Connecting SITRANS Probe LR (Page 23).

WARNING

Loss of type of protection
Risk of explosion. Damage to device if the enclosure is open or not properly closed. The

type of protection specified on the nameplate or in Approvals (Page 83) is no longer

guaranteed.

•

Make sure that the device is securely closed.

6.2

Local commissioning

6.2.1

Activating SITRANS Probe LR

Note
Keep infrared devices such as laptops and cell phones away from SITRANS Probe LR to

prevent inadvertent operation.

Power up the instrument. SITRANS Probe LR starts in RUN mode, and detects the material

level. It displays the material level (in meters) referenced from Empty (process empty level).

This is the default startup mode.

6.2.2

Operating SITRANS Probe LR

SITRANS Probe LR has two modes of operation: RUN and PROGRAM.

Содержание 7ML5430
















































































































Результаты поиска

Содержание 7ML5430

Отзывы:

Siemens 7ML5430, Руководство по эксплуатации, Страница: 26 / 111

Результаты поиска

Содержание 7ML5430

Отзывы: