Siemens 7ME6810 Скачать руководство пользователя страница 36

Страница: 36 / 170

5.3

Power supply

Connection diagram for 115 to 230 V AC (mains) or 12/24 V AC/DC (line) power supply

L112.1

Backup battery connection

①

Red

②

Black

MAG 8000 PCB connection

③

Blue

④

Yellow

External power supply con‐

nection

⑤

Blue (Neutral / -)

⑥

Brown (Line / +)

Shielding

⑦

Shielding wire

It is mandatory to connect the shielding wire to the MAG 8000 device earthing; otherwise IrDA

communication will not work satisfactorily.

115 to 230 V AC (mains) power supply

Mains power input

Factory mounted PUR cable with 2 x 1 mm

(brown wire, blue wire) cable length = 3 m

Brown wire - L (Line, +) and blue wire - N (Neutral, -)

Mains power output

Female battery connector with blue and yellow wires; blue wire is ground. Female battery con‐

nector has to be connected to male connector 3.6 V DC on PCB board

Battery backup input

Male battery connector with black and red wires; black wire is ground. Male battery connector has

to be connected to female connector on backup battery

Functional ground

Black wire with terminal must be connected to the device encapsulation with a screw

Mains power supply has to be connected to a switch near water meter according to IEC 61010-1 clause 5.4.3.d

12/24 V AC/DC (line) power supply

Line power input

Factory mounted PUR cable with 2 x 1 mm

(brown wire, blue wire) cable length = 3 m

Brown wire - L (line, hot, positive) and blue wire - N (neutral, cold, negative)

Line power output

Female battery connector with blue and yellow wires; blue wire is ground. Female battery con‐

nector has to be connected to male connector 3.6 V DC on PCB board

Connecting
5.3 Power supply

SITRANS FM MAG 8000

Operating Instructions, 03/2020, A5E03071515-AH

Содержание 7ME6810











































































































































































Результаты поиска

Содержание 7ME6810

Отзывы:

Siemens 7ME6810, Руководство по эксплуатации, Страница: 36 / 170

Результаты поиска

Содержание 7ME6810

Отзывы: