Siemens 7ME6810 Скачать руководство пользователя страница 26

Страница: 26 / 170

4.3

Grounding

The sensor body must be grounded using grounding/bonding straps and/or grounding rings to

protect flow signal against stray electrical noise and/or lightning. This ensures that noise is

carried through sensor body and that the measuring area within sensor body is noise-free.

Note
Grounding connector rotated by 90°
For sensor sizes between DN 25 (1") and DN 300 (12"), the grounding connector on the sensor

is rotated by 90°.

Metal pipes

Connect straps to both flanges with 6 mm (1/4") screws.

①

Metal pipes

②

Grounding straps (rotated by 90° on DN 350 to DN 1200)

Grounding straps are part of delivery and pre-mounted on water meter.

Installing/Mounting
4.3 Grounding

SITRANS FM MAG 8000

Operating Instructions, 03/2020, A5E03071515-AH

Содержание 7ME6810











































































































































































Результаты поиска

Содержание 7ME6810

Отзывы:

Siemens 7ME6810, Руководство по эксплуатации, Страница: 26 / 170

Результаты поиска

Содержание 7ME6810

Отзывы: