Siemens 7ME6810 Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 170

Siemens 7ME6810 Скачать руководство пользователя страница 129

5. Change units description in parameters 8 and 9, see Unit conversion table.
6. Change units factor in parameters 300 and 301, see Unit conversion table.
7. Change maximum flow rate Qn (Q3) to new unit selection in parameter 10.
8. Select display unit in parameter 306.
9. Download each parameter to meter.
10.Remove hardware key.
11.Re-assemble meter.

Note
Important
The service mode opens many parameters. If these parameters are changed, it can

seriously affect meter accuracy and operation. Be careful when writing new parameter

values as meter has no default settings to return to.

C.6

Output configuration

Pulse output can be configured as volume pulse, alarm or call-up. Default factory setting is with

output A enabled for forward flow and output B for alarm output.

Output configuration in Flow Tool
Select "I/O and Com.Setup". The software window shows the parameters for output

configuration. Each parameter has its own guideline for selecting the correct parameter setting.

To see how the outputs work, please see "Output characteristics" (Page 98).

Flow Tool

C.6 Output configuration

SITRANS FM MAG 8000

Operating Instructions, 03/2020, A5E03071515-AH

129

«
...
127
128
129
130
131
...
»

Содержание 7ME6810











































































































































































Отзывы:

Нет отзывов