Siemens 7ME652 Скачать руководство пользователя страница 47

Страница: 47 / 86

Diagnostics and Troubleshooting

7.1

Sensor check

Requirement

To check the SITRANS FM sensors the following test instruments will be required:
● Digital Meter/Multimeter
● Megger
● (Moving Coil Meter)

Sensor check

Remove the transmitter from the sensor or remote position before making the following checks.

Coil resistance check

● Measure the coil resistance between connection numbers 85 and 86 using a digital meter.

Resistance should be within range stated in Coil resistance table.

A low reading may indicate moisture within the coil housing or shorted coil tums.
A high reading would indicate an open circuit coil.

Note
In case of deviation from nominal coil values, the sensor is damaged and must be replaced

Coil insulation check

WARNING

Potential hazard!
Only carry our a coil insulation check in non-hazardous area!

● Megger between connection number 85 and the sensor body.

The resistance should be above 20 MΩ.

A low megger reading would indicate the coil insulation is breaking down. This is normally due

to fluid ingress into the coil housing.
Sensors with an insulation resistance down to 1 MΩ may still work satisfactorily but this is not

guaranteed.

SITRANS FM MAG 5100 W

Operating Instructions, 01/2020, A5E03063678-AC

Содержание 7ME652























































































Результаты поиска

Содержание 7ME652

Отзывы:

Siemens 7ME652, Руководство по эксплуатации, Страница: 47 / 86

Результаты поиска

Содержание 7ME652

Отзывы: