manualshive.com logo in svg

Siemens 7ME652, Руководство по эксплуатации, Страница: 30 / 86

Поделиться
Скачать
Siemens 7ME652 Скачать руководство пользователя страница 30

Torque calculations
All values are theoretical and are calculated making the following assumptions:
1. All bolts are new and material selection is according to EN 1515-1 table 2.
2. Gasket material not exceeding 75 shore A durometer is used between the flowmeter and 

mating flanges.

3. All bolts are galvanized and adequately lubricated.
4. The values are calculated for use with carbon steel flanges.
5. Flowmeter and mating flanges are correctly aligned.

4.5

Potential equalization

To obtain optimum results from the measuring system, the sensor must have the same 

electrical potential as the liquid being measured.
This is achieved by means of built-in grounding electrodes.

Figure 4-8

Potential equalization with earthing electrodes   

Cathodic protected piping

Special attention must be paid to systems with cathodic protection.   

WARNING

Use in hazardous area!
Cathodic pipe protection is not allowed in hazardous areas

Installing/Mounting
4.5 Potential equalization

SITRANS FM MAG 5100 W

30

Operating Instructions, 01/2020, A5E03063678-AC

Содержание 7ME652























































































Отзывы:

Нет отзывов