Siemens 7ME652 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 86

Siemens 7ME652 Скачать руководство пользователя страница 11

Safety notes

2

This device left the factory in good working condition. In order to maintain this status and to

ensure safe operation of the device, observe these instructions and all the specifications

relevant to safety.
Observe the information and symbols on the device. Do not remove any information or symbols

from the device. Always keep the information and symbols in a completely legible state.

CAUTION

Correct, reliable operation of the product requires proper transport, storage, positioning and

assembly as well as careful operation and maintenance.
Only qualified personnel should install or operate this instrument.

Note
Alterations to the product, including opening or improper modifications of the product are not

permitted.
If this requirement is not observed, the CE mark and the manufacturer's warranty will expire.

2.1

Laws and directives

Observe the safety rules, provisions and laws applicable in your country during connection,

assembly and operation. These include, for example:
● National Electrical Code (NEC - NFPA 70) (USA)
● Canadian Electrical Code (CEC) (Canada)
Further provisions for hazardous area applications are for example:
● IEC 60079-14 (international)
● EN 60079-14 (EU)

SITRANS FM MAG 5100 W

Operating Instructions, 01/2020, A5E03063678-AC

11

«
...
9
10
11
12
13
...
»

Содержание 7ME652























































































Отзывы:

Нет отзывов