manualshive.com logo in svg

Siemens 7ME305, Руководство по эксплуатации, Страница: 72 / 124

Поделиться
Скачать
Siemens 7ME305 Скачать руководство пользователя страница 72

Required forms

• Delivery note

• Return goods delivery note (

https://www.siemens.com/processinstrumentation/

returngoodsnote

)

with the following information:

– Product (item description)

– Number of returned devices/replacement parts

– Reason for returning the item(s)

• Decontamination declaration (

https://www.siemens.com/sc/

declarationofdecontamination

)

With this declaration you warrant "that the device/replacement part has been carefully 
cleaned and is free of residues. The device/replacement part does not pose a hazard for 
humans and the environment."
If the returned device/replacement part has come into contact with poisonous, corrosive, 
flammable or water-contaminating substances, you must thoroughly clean and 
decontaminate the device/replacement part before returning it in order to ensure that all 
hollow areas are free from hazardous substances. Check the item after it has been cleaned.
Any devices/replacement parts returned without a decontamination declaration will be 
cleaned at your expense before further processing.

8.3

Keying in sensor data

The following step-by-step procedure only applies to:

• FUS060 transmitters with SONOKIT sensors

• Replacement transmitters

NOTICE
SONO 3100 and SONO 3300

All FUS060 transmitters calibrated with sensors SONO 3100 or SONO 3300 are delivered with 
sensor data preset from factory. The data should not be changed

The step-by-step procedure describes the required parameters/data to be entered and the 
sequence of entering them in order to configure the transmitter correctly for a given pipe 
application.

Note

The pipe data are taken from the SONOKIT sensor geometry measurement report or from 
another sensor data sheet or calibration report.

Service and maintenance
8.3 Keying in sensor data

SITRANS FUS060 with PROFIBUS PA

72

Operating Instructions, 09/2021, A5E02225054-AD

Содержание 7ME305





























































































































Отзывы:

Нет отзывов