Siemens 7ME305 Скачать руководство пользователя страница 107

Страница: 107 / 124

Menu
code

Device function,
Parameters

Description

Factory setting

Setting options

Read
or write

1.1.5

LCD lighting

Switch LCD on/off (On at infrared key
operation; automatically reset to Off
at power-off)

Off

On (turns off auto‐
matically after 1
hour)
Off (turns off auto‐
matically after 10 mi‐
nutes)

Write

1.1.6

Multi display

Display of two measured values in
lines 1 and 2

Line 1: Flow
Line 2: Totalizer

See menu 1.1.2
See menu 1.1.3

Read

1.2

Flow

1.2

Flow

Flow in metering tube

Actual metering val‐
ue

For unit see menu
3.1.1

Read

1.3

Totalizer

1.3.1

Total. forward

Totalizer forward

Actual value is shown Units selectable in

menu 3.4.1

Read

1.3.2

Total. reverse

Totalizer reverse

Actual value is shown Units selectable in

menu 3.5.1

Read

1.3.3

Total net

Totalizer difference Forward -reverse Actual value is shown Units selectable in

menu 3.6.1

Read

1.3.4

Settings (all)

All totalizers will be set to zero. (Inde‐
pendent setting of totalizers in menu
3.4, 3.5, 3.6)

No action

No action
Reset + stop
Reset + start

Write

1.4

Flow velocity

1.4

Flow velocity

Flow velocity in metering tube

Actual value is shown m/s (range -12 to +12

m/s)

Read

1.5

Sound velocity

1.5

Sound velocity

Sound velocity in medium

Actual value is shown m/s

Read

1.6

Amplitude US

1.6

Amplitude US

Relative ultrasonic amplitude of re‐
ceived ultrasonic signals (reference
water). Depending on paths activa‐
ted (up to 4 values).

Actual value is shown Display in %

Read

1.7

Frequency

1.7

Frequency

Frequency output value

Actual value is shown Hz

Read

D.1.2

Menu 2 - Diagnostics

Menu
code

Device function,
Parameters

Description

Factory setting

Setting options

Read
or write

2.1

Device status

2.1

Device status

Error messages are shown

"OK"

Only read
See table in chapter
6.2

Read

HMI menu structure

D.1 Menu items (FW Rev. 4.00.00)

SITRANS FUS060 with PROFIBUS PA
Operating Instructions, 09/2021, A5E02225054-AD

107

Содержание 7ME305





























































































































Результаты поиска

Содержание 7ME305

Отзывы:

Siemens 7ME305, Руководство по эксплуатации, Страница: 107 / 124

Результаты поиска

Содержание 7ME305

Отзывы: