Siemens 7MB2041 Скачать руководство пользователя страница 42

Страница: 42 / 152

Commissioning

4.3 Commissioning and operation

OXYMAT 64

Operating Instructions, 06/2008, A5E00880383-03

Span adjustment

The setpoint should be as close as possible to the full-scale value (at least 70% of the

respective span). Connect the corresponding calibration gas for the span adjustment. The

setpoint is also entered using function 22.

4.3.4

General information on calibration

Note
Calibration is only possible when the device is in the "Measure" operating state.

Zero point

The zero point is calibrated using function 20. The device displays both the setpoint and

actual value.

Note
Note that this function can only be activated if AUTOCAL (function 24) is deactivated.

Single / total calibration

A single or total calibration is selected using function 23.
Single calibration means that each measuring range is calibrated using a separate

calibration gas.
During a total calibration, the measuring ranges defined using function 41 are calibrated

together.

Sensitivity

Select function 21 and carry out the desired calibration. Note that this function can only be

activated if AUTOCAL (function 24) is deactivated. If the total calibration was activated

previously, all measuring ranges are then calibrated.
If you have selected single calibration (total calibration deactivated), repeat the calibration

procedure for each measuring range individually with the corresponding calibration gases.

(In function 22, a calibration gas must be entered for every measuring range!)

Содержание 7MB2041

























































































































































Результаты поиска

Содержание 7MB2041

Отзывы:

Siemens 7MB2041, Руководство по эксплуатации, Страница: 42 / 152

Результаты поиска

Содержание 7MB2041

Отзывы: