Siemens 6GT2002-0HD01 Скачать руководство пользователя страница 49

Страница: 49 / 72

Diagnostics and error messages

7.5 Diagnostics of the RF170C communications module

SIMATIC RF170C
Operating Instructions, 02/2022, J31069-D0176-U001-A6-7618

Diagnostics alarms

With the diagnostics alarms, a distinction is made between incoming and outgoing

diagnostics.

Incoming diagnostics

An event occurs and triggers a diagnostics alarm. Depending on the parameter assignment,

the "Ext_Diag" bit is set.

Outgoing diagnostics

The event is no longer pending and a diagnostics alarm is output without a set “Ext_Diag” bit.

In the case of events that are only pending for a moment, cancellation is delayed by 3

seconds.
The hard errors are supported by text messages stored in the GSD/GSDML file.

7.5

Diagnostics of the RF170C communications module

Diagnostics data of the RF170C is mapped to the channel-related diagnostics of the ET

200pro.
The data in the table below apply for the RF170C:

Table 7- 4

Diagnostics of the RF170C

Content

Value

Meaning

Channel

assignment

80h

Reader 1

81h

Reader 2

Channel type

Input/output channel

Channel resolution 101

Word

Error type

00001

Short-circuit

(voltage supply to the reader has a short circuit)

00110

Wire break

(connection to the reader is interrupted)

01001

Error

(internal module error has occurred on the RF170C)

10000

Parameter assignment error

(RF170C does not have parameters)

10001

No encoder voltage or load voltage

(supply voltages not present or too low)

Содержание 6GT2002-0HD01









































































Результаты поиска

Содержание 6GT2002-0HD01

Отзывы:

Siemens 6GT2002-0HD01, Руководство по эксплуатации, Страница: 49 / 72

Результаты поиска

Содержание 6GT2002-0HD01

Отзывы: