Siemens 6GT2002-0HD01 Скачать руководство пользователя страница 48

Страница: 48 / 72

Diagnostics and error messages

7.4 Parameterization of the diagnostics

SIMATIC RF170C

Operating Instructions, 02/2022, J31069-D0176-U001-A6-7618

I&M data

Access

Default

Explanation

Maintenance data 1: Index 2 (data record 232 or =0xAFF1)

TAG_FUNCTION

read / write (32

bytes)

Here, enter an ID for the module here that

is unique in the entire plant.

TAG_LOCATION

read / write (22

bytes)

Here enter the installation location of the

module.

Maintenance data 2: Index 3 (data record 233 or =0xAFF2)

INSTALLATION_DATE

read / write (16

bytes)

Here, enter the installation date of the

module.

RESERVED

read / write (38

bytes)

Reserved

Maintenance data 3: Index 4 (data record 234 or =0xAFF3)

DESCRIPTOR

read / write (54

bytes)

Here, enter a comment describing the

module.

7.4

Parameterization of the diagnostics

In addition to the PROFIBUS / PROFINET standard diagnostics, the RF170C offers user-specific

diagnostics data integrated in the diagnostics of the interface module.
The diagnostics data can be read out as follows:
•

as plain text in the STEP 7 user interface

•

on PROFIBUS DP

–

Read out with SFC 13 slave diagnostics and store in the data area of the application

•

on PROFINET IO

–

Read data records from the IO device with SFB 52

–

Receive alarms from the IO device with SFB 54

•

Evaluation with FB 125 or FC 125

Parameter assignment options

•

None

No other diagnostics data is reported, apart from standard diagnostics.

•

Hard errors

Extended diagnostics messages are generated in the case of the following events.

–

Hardware fault (memory test)

–

Firmware error (checksum)

–

Connection to reader lost

–

Short-circuit fault/interruption, if supported by hardware

–

Firmware update (message at start/end)

In the case of this diagnostics, the “Ext_Diag” bit is set, that is, it is treated as high-priority

diagnostics information in the controller (SF-LED is lit)

Содержание 6GT2002-0HD01









































































Результаты поиска

Содержание 6GT2002-0HD01

Отзывы:

Siemens 6GT2002-0HD01, Руководство по эксплуатации, Страница: 48 / 72

Результаты поиска

Содержание 6GT2002-0HD01

Отзывы: