Siemens 6GT2002-0HD01 Скачать руководство пользователя страница 39

Страница: 39 / 72

Parameter settings

5.6 Parameters and commands of FB 45

SIMATIC RF170C
Operating Instructions, 02/2022, J31069-D0176-U001-A6-7618

5.6

Parameters and commands of FB 45

Parameters of FB 45

Assignment is made in UDT 10.

Table 5- 5

Parameters of FB 45

Address

Name

Permissible values

Comment

+0.0

ASM_address

256, 260, 264, 268,

...

Each RF170C occupies four bytes of

I/O in the I/O area of the control

unit

+2.0

ASM_channel

1, 2

+8.0

MDS_control

B#16#0, 1

0 = no presence check

1 = presence check

+9.0

ECC_mode

TRUE, FALSE

+9.1

RESET_long

TRUE, FALSE

TRUE,

if MOBY mode = 5 (MOBY U/D, RF300)

+10.0

MOBY_mode

B#16#1, 4, 5, 6, 7,

8, 9, A, B

Special features of the MOBY I dialog

(8):

•

Write/read device must be type

SLG4x.

•

The VMDS memory size is 16KB. The

INIT command for the VMDS must be

specified using 4000 hex.

+11.0

scanning_time

MOBY I:

B#16#00 ... FF

A value not equal to 00 is only

practical if MOBY_mode has been

parameterized accordingly.

MOBY D, RF300 reserved (00)

MOBY U:

B#16#00 ... C8

+12.0

option_1

B#16#00, 02, 04

+13.0

distance_limiting

MOBY U (normal

output power):

B#16#05, 0A, 0F, 14,

19, 1E, 23

MOBY U / D

MOBY U (reduced

output power):

B#16#85, 8A, 8F, 94,

99, 9E, A3

MOBY D, RF290R:

B#16#02 ... 28

RF380R:

B#16#02 ... 08

+14.0

multitag

B#16#1

MOBY U/D, RF300

+15.0

field_ON_control

MOBY U:

B#16#0, 1, 2, 3

MOBY U/D, RF300

MOBY D, RF300:

B#16#0

+16.0

field_ON_time

MOBY U:

B#16#00 ... FF

MOBY U/D

RF300 reserved (00)

MOBY D:

B#16#00, 01

You will find detailed information on the parameters of FB 45 in combination with the

RF620R/RF630R readers in the section “Parameter assignment > Parameter assignment

RF620R/RF630R with FB 45 > Input parameters" in the "Configuration Manual

RF620R/RF630R".

Содержание 6GT2002-0HD01









































































Результаты поиска

Содержание 6GT2002-0HD01

Отзывы:

Siemens 6GT2002-0HD01, Руководство по эксплуатации, Страница: 39 / 72

Результаты поиска

Содержание 6GT2002-0HD01

Отзывы: