manualshive.com logo in svg

Siemens 6GT2002-0HD01, Руководство по эксплуатации, Страница: 11 / 72

Поделиться
Скачать
Siemens 6GT2002-0HD01 Скачать руководство пользователя страница 11

 

Description 

 

2.2 Design 

SIMATIC RF170C 
Operating Instructions, 02/2022, J31069-D0176-U001-A6-7618 

11

 

2.2

 

Design 

2.2.1

 

Configuration 

This chapter describes a sample configuration of an ET 200pro with RF170C. 

Structure 

The ET 200pro is installed on a rack and consists basically of the following:  
•

 

an interface module that transfers data to the DP master or IO controller, 

•

 

or a CPU, 

•

 

up to 9 RF170C modules, 

•

 

Connection modules for an interface module in various designs for 

–

 

Interface modules (PROFIBUS DP, PROFINET IO, power supply) 

–

 

Communications modules 

This allows you create the setup precisely the meet your local requirements. 
The simple handling of the ET 200pro ensures fast commissioning and easy maintenance.  

 

 

Note 
Configuring the ET 200pro 

The maximum electrical setup can be checked with the TIA Selection Tool. We recommend 

use of the tool because the maximum setup cannot be achieved with all reader 

configurations. 
You will find the tool on the Internet on the page of the “Siemens homepage 

(

http://w3.siemens.com/mcms/topics/en/simatic/tia-selection-tool/Pages/tab.aspx

)“. 

 

 

Содержание 6GT2002-0HD01









































































Отзывы:

Нет отзывов