Siemens 6GK5748-1GY01-0AA0 Скачать руководство пользователя страница 44

Страница: 44 / 91

Installation and removal

5.2 Types of installation

SCALANCE W1788-x / W1748-1

Operating Instructions, 03/2022, C79000-G8976-C484-05

5.2

Types of installation

Note

The device is only approved for operation in closed rooms. Note the following

environmental conditions.
Antennas, in particular directional antennas, must be mounted in keeping with their

characteristics (refer to the technical specifications of the antenna --> Radiation pattern

diagrams).

For the device the following types of installation are permitted:
•

Wall mounting

•

Ceiling mounting

•

Mounting on a DIN rail

•

Mounting on an S7-300 or S7-1500 mounting rail

CAUTION

Danger of injury by falling objects

If the SCALANCE W is subjected to very strong vibration (> 10 g), mounting on a 35 mm

DIN rail does not provide adequate support. Under such conditions, the device can

come out of the mounting and may cause injury.
In this case, install the device on a mounting rail or on a wall.

Содержание 6GK5748-1GY01-0AA0




























































































Результаты поиска

Содержание 6GK5748-1GY01-0AA0

Отзывы:

Siemens 6GK5748-1GY01-0AA0, Руководство по эксплуатации, Страница: 44 / 91

Результаты поиска

Содержание 6GK5748-1GY01-0AA0

Отзывы: