Siemens 6ES7144-5KD50-0BA0 Скачать руководство пользователя

Страница: 38 / 55

Interrupts/diagnostics alarms

5.2 Interrupts

Analog input module AI 4xRTD/TC 4xM12 (6ES7144-5KD50-0BA0)
Equipment Manual, 08/2020, A5E48753535-AA

5.2

Interrupts

The AI 4xRTD/TC 4xM12 analog input module supports diagnostic and hardware interrupts.

Diagnostic interrupt

The table below shows the events for which the analog input module returns a diagnostic

interrupt, depending on the parameter assignment.

Table 5- 3

Diagnostic interrupts

Measure-

ment type

Diagnostics

Wire

break

High limit

violated

Low limit

violated

Error

Parame-

ter as-

signment

error

Reference

channel

error

Hardware

interrupt

lost

Voltage

Resistance

Thermal

resistor

Thermocou-

ple

Hardware interrupt

The analog input module generates a hardware interrupt with the following events:
•

Low limit 1 violated

•

High limit 1 violated

•

Low limit 2 violated

•

High limit 2 violated

Detailed information on the event is available in the hardware interrupt organization block

with the instruction "RALRM" (Read additional interrupt information) and in the STEP 7 online

help.
The start information of the organization block includes information on which channel of the

analog input module triggered the hardware interrupt.

Note
High limit violation of 2 limits

If two limits are violated at the same time, limit 1 is always signaled first, followed by limit 2.

Содержание 6ES7144-5KD50-0BA0
























































Результаты поиска

Содержание 6ES7144-5KD50-0BA0

Отзывы:

Похожие инструкции для 6ES7144-5KD50-0BA0

Бренды по названию

Популярные бренды

Siemens 6ES7144-5KD50-0BA0, Руководство пользователя

Результаты поиска

Содержание 6ES7144-5KD50-0BA0

Отзывы:

Похожие инструкции для 6ES7144-5KD50-0BA0

Бренды по названию

Популярные бренды