Siemens 6EP4131-0GB00-0AY0 Скачать руководство пользователя страница 46

Страница: 46 / 264

Description, device design, dimension drawing

2.4 Operating displays and signaling

SITOP UPS1600 / BAT1600 / UPS1100

Equipment Manual, 07.2021, A5E37775406-11-76

States of the LEDs

Signaling

6EP4132-0JA00-0AY0 (2.5 Ah)

6EP4133-0GA00-0AY0 (3.2 Ah)

6EP4134-0JA00-0AY0 (7.5 Ah)

6EP4135-0GE00-0AY0 (12 Ah)

6EP4137-0GE00-0AX0 (38 Ah)

Off

Module runs up, DC-UPS defective (critical hardware fault)

Flashing green

(0.25/0.25)

Battery is being replaced (button pressed, reset service life)

Flashing green

(1/1)

Battery successfully replaced (LED flashes for 5 s)

Flashing green

(1/1)

Battery replacement recommended (SoH ≤ 20

Green

Battery module OK

Flashing yellow

(0.25/0.25)

End of the battery service life reached (SoH = 0 %) or battery test

negative → battery must be replaced, buffer mode possible

Flashing yellow

(1/1)

Temperature outside the valid range, communication cable interrupted or

different battery types being used → restricted charge operation

Yellow

Selected buffer time cannot be attained

Flashing red (1/1) Battery replacement canceled (LED flashes for 5 s)

Red

Fuse ruptured/not inserted, power cable interrupted, 1 battery in the mod-

ule is not connected, battery pack voltage is not symmetrical or reset button

is pressed > 2 s

2.4.3

SITOP UPS1100

Figure 2-22 Example 6EP4131-0GB00-0AY0

States of the LEDs

Signaling

6EP4131-0GB00-0AY0 (1.2 Ah)

6EP4132-0GB00-0AY0 (2.5 Ah)

6EP4133-0GB00-0AY0 (3.2 Ah)

6EP4133-0JB00-0AY0 (5 Ah)

6EP4134-0GB00-0AY0 (7 Ah)

6EP4135-0GB00-0AY0 (12 Ah)

Off

Module runs up, DC-UPS defective (critical hardware fault)

Green

Battery module OK

Flashing yellow

(1/1)

Battery outside the permitted temperature range

Yellow

Selected buffer time cannot be attained

Red

Battery module fault, maintenance required (incorrect polarity, battery

module not connected, high ohmic battery module connection, battery

deep discharged, fuse defective/ruptured, asymmetrical cell voltage, battery

R test unsuccessful)

Содержание 6EP4131-0GB00-0AY0









































































































































































































































































Результаты поиска

Содержание 6EP4131-0GB00-0AY0

Отзывы:

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренды по названию

Популярные бренды

Siemens 6EP4131-0GB00-0AY0, Руководство по эксплуатации оборудования

Результаты поиска

Содержание 6EP4131-0GB00-0AY0

Отзывы:

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренды по названию

Популярные бренды