Siemens 6EP4131-0GB00-0AY0 Скачать руководство пользователя страница 226

Страница: 226 / 264

Installation

7.8 Maintenance

SITOP UPS1600 / BAT1600 / UPS1100

226

Equipment Manual, 07.2021, A5E37775406-11-76

Note

When battery modules are connected in parallel, only the fuse of the battery module where

the battery is replaced must be removed. Before recommissioning the battery module in the

parallel circuit, all battery modules must be charged to the same level (to avoid very high

recharging currents).

Note

Dispose of old batteries in the discharged state according to the applicable regulations.

Note

After the battery has been correctly replaced, the calculated battery health is reset to 100 %.

7.8.3

Battery replacement SITOP UPS1100

See Figure 7-7 Maintenance (Page 227) and Figure 7-8 Wiring schematic (Page 227)
1.

Release screws

⑨

using a Torx T10 screwdriver.

Open the cover.

Press button

⑧

for at least 2 s.

LED

④

flashes

Remove fuse

③

Replace the batteries.

Press the button for at least 2 s
LED

④

stops flashing and lights continuously.

Insert the fuse.

Close the cover (screw).

Pressing the button resets the following functions:
•

Operating hours counter

•

Buffer time counter

•

Summed charge current

•

Summed load current

•

Calculated capacity

•

Calculated battery status

Note

Replace the battery only in normal operation, not in backup operation.

Содержание 6EP4131-0GB00-0AY0









































































































































































































































































Результаты поиска

Содержание 6EP4131-0GB00-0AY0

Отзывы:

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренды по названию

Популярные бренды

Siemens 6EP4131-0GB00-0AY0, Руководство по эксплуатации оборудования

Результаты поиска

Содержание 6EP4131-0GB00-0AY0

Отзывы:

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренды по названию

Популярные бренды