Siemens 6EP4131-0GB00-0AY0 Скачать руководство пользователя страница 179

Страница: 179 / 264

Engineering and remote access

3.10 OPC UA server

SITOP UPS1600 / BAT1600 / UPS1100
Equipment Manual, 07.2021, A5E37775406-11-76

179

3.10.6.26

Additional parameters

These nodes are listed at the first level in the object tree

Display name

Data type

Definition

Description

DeviceManual

String

PropertyType

Address (path in the file system or URL / web address) of the

operating instructions for the device.

Hardware Revision

String

PropertyType

Revision status of the device hardware.

Manufacturer

LocalizedText

PropertyType

Name of the company that manufactured the device.

Model

LocalizedText

PropertyType

Model

ModuleIdentNumber

UInt32

PropertyType

Module identification number

OrderNumber

String[20]

PropertyType

Article number

RevisionCounter

Int32

PropertyType

Incremental counter that specifies how often the static data

in the device was modified.

SerialNumber

String

PropertyType

ID, which uniquely identifies the device for the device manu-

facturer.

SoftwareRevision

String

PropertyType

Revision status of the device software.

3.10.7

OPC UA performance

OPC UA provides the option of collectively transferring modified actual values in the form of a

subscription. The minimum pole interval of such a subscription is 100 ms. A maximum of

150 data nodes can be simultaneously monitored, independent of whether these data nodes

are assigned one or various subscriptions.
OPC UA does not support any type of realtime communication, neither for actual values (read

data) nor for setpoints (written data). As a consequence, it is not possible to specify an

update/refresh rate or a maximum data flow rate.

3.10.8

Recommissioning after a basic device has been replaced - or after restoring

the factory settings

If, for service reasons it is necessary to replace the basic unit - or store the factory settings,

then please observe the following notes:
1.

Brand new basic units or basic units, where the factory settings have been restored, have no

IP address. However, this is generally necessary so that the device can be accessed using

OPC UA. Proceed as described in Chapter "General (Page 142)", Section "Communication

interface" to assign the device a certain IP address.

The configuration must be loaded to the device. This can be done in the following ways:

•

Proceed as described in Chapter "Load / Save (Page 155)" to load a valid configuration into

the device (previously saved via web server).

•

Load a valid configuration to the device via OPC UA. Ensure that the necessary user

account is available in the device for access via OPC UA. The latter can be created using a

web server, see Chapter "Web server (Page 144)".

Содержание 6EP4131-0GB00-0AY0









































































































































































































































































Результаты поиска

Содержание 6EP4131-0GB00-0AY0

Отзывы:

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренды по названию

Популярные бренды

Siemens 6EP4131-0GB00-0AY0, Руководство по эксплуатации оборудования

Результаты поиска

Содержание 6EP4131-0GB00-0AY0

Отзывы:

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренды по названию

Популярные бренды