Siemens 6EP4131-0GB00-0AY0 Скачать руководство пользователя страница 170

Страница: 170 / 264

Engineering and remote access

3.10 OPC UA server

SITOP UPS1600 / BAT1600 / UPS1100

170

Equipment Manual, 07.2021, A5E37775406-11-76

Display name

Data type

Definition

Description

AlarmLow

VoltageMode

Boolean

PropertyType

Input voltage of SITOP UPS1600 is too low. The buffer of the

SITOP UPS1600 is not operational.

AlarmNoCharging

ManualDeactivated

Boolean

PropertyType

Charging function was deactivated by a control command

AlarmOutputTurnedOff Boolean

PropertyType

Output of SITOP UPS1600 has been switched off due to the

execution of a command or because an error situation has

occurred (e.g. temperature or output current too high).

AlarmOutputTurnedOn Boolean

PropertyType

Output of SITOP UPS1600 has been switched on again due

to the execution of a command or because an error situation

has been remedied.

AlarmOverCurrent

Boolean

PropertyType

Output current of SITOP UPS1600 is too high. Output is

switched off for 20 s. The output is switched on again after

20 s.

AlarmResetExecuted

Boolean

PropertyType

Input voltage connected to SITOP UPS1600 was already OK

before the buffer time expired. Connected devices are reset

by switching off the SITOP UPS1600 outputs for the parame-

terized time.

AlarmSurplusBattery

Boolean

PropertyType

More than 6 batteries are connected. Connect max. of

6 batteries to the Energy Storage Link.

AlarmUnknownBattery Boolean

PropertyType

Data from the battery cannot be read correctly. Battery is

defective or not supported by SIEMENS.

AlarmWrongBattery

Polarity

Boolean

PropertyType

Wrong battery polarity - check battery connections.

3.10.6.8

Battery

Display name

Data type

Definition

Description

BatteryCapacity

Setpoint

Float

AnalogItemType Total battery capacity in Ah

BatteryDefectVoltage

Setpoint

Float

AnalogItemType If battery voltage is lower than this value, the battery is con-

sidered defective.

BatteryIgnoreCoding

Setpoint

Boolean

PropertyType

When this parameter is set to '1', data from the coded bat-

tery is ignored. The data is taken from the parameter as-

signment in this case.

BatteryInspection

TimeSetpoint

Byte

PropertyType

Battery test interval in hours

3.10.6.9

Buffering

Display name

Data type

Definition

Description

BufferExpected

CurrentSetpoint

Float

AnalogItemType Estimated average output current during buffer mode

BufferThreshold

Setpoint

Float

PropertyType

Trigger voltage for buffering - buffering is activated below

this value

BufferTime2Setpoint

UInt16

AnalogItemType Additional buffer time after PC shutdown (valid only in con-

junction with SITOP Manager)

BufferTimeSetpoint

UInt16

AnalogItemType Desired buffering time before device switches off

BufferingEnableSet-

point

Boolean

PropertyType

Enable buffering

Содержание 6EP4131-0GB00-0AY0









































































































































































































































































Результаты поиска

Содержание 6EP4131-0GB00-0AY0

Отзывы:

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренды по названию

Популярные бренды

Siemens 6EP4131-0GB00-0AY0, Руководство по эксплуатации оборудования

Результаты поиска

Содержание 6EP4131-0GB00-0AY0

Отзывы:

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренды по названию

Популярные бренды