Siemens 6EP4131-0GB00-0AY0 Скачать руководство пользователя страница 107

Страница: 107 / 264

Engineering and remote access

3.6 Cyclic and acyclic data

SITOP UPS1600 / BAT1600 / UPS1100
Equipment Manual, 07.2021, A5E37775406-11-76

107

Slot

Subslot Data

Description

Data size

Battery change

recommended

Battery replacement recommend-

ed: Battery capacity is insufficient

to achieve the specified buffer

time:
•

0: no

•

255: yes

Unsigned8

Not used

Unsigned8

Battery charge level

Battery charge level in %:
•

0-100: 0-100%

•

255: unknown battery

Unsigned8

Battery connection

maintenance

from V2.1

Connection to the battery inter-

rupted: Check the connection and

fuse:
•

0: no maintenance required

•

255: maintenance required

Unsigned8

3.6.2

Reading and writing data sets

An overview of all data sets, which are communicated between the SITOP UPS1600 and the

PROFINET IO-Controller is provided in the following table. Here, a distinction is made

between the following data sets:
•

Reading data sets:

Data that is sent from the SITOP UPS1600 to the

PROFINET IO-Controller.

•

Writing data sets:

Data that is sent from the PROFINET IO-Controller to the SITOP

UPS1600.

Index

Slot

Sub-

slot

Data set

Type

Description

Data size

0x0001 0

Buffering parameters

Reading/

writing

Buffer parameters.

14 bytes

16 bytes

(from V2.4)

0x0002 0

Battery parameters

Reading/

writing

Parameters of the connected battery

modules

5 bytes

0x0003 0

Charging parameters

Reading/

writing

Charge parameters of the connected

battery modules

4 bytes

0x0004 0

Reset parameters

Reading/

writing

Reset parameters.

1 byte

0x0005 0

Battery information

parameters

Reading

Information about the connected SITOP

BAT1600 or SITOP UPS1100 battery

modules. This information is available

via the link "Energy Storage".

1024 bytes

556 bytes

(from V2.4)

0x0006 0

Device information

Parameters

Reading

Information about the

SITOP UPS1600.

124 bytes

0x0007 0

Hardware settings

parameters

Reading

Hardware settings of the

SITOP UPS1600 (settings that were

made at the front of the device).

8 bytes

Содержание 6EP4131-0GB00-0AY0









































































































































































































































































Результаты поиска

Содержание 6EP4131-0GB00-0AY0

Отзывы:

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренды по названию

Популярные бренды

Siemens 6EP4131-0GB00-0AY0, Руководство по эксплуатации оборудования

Результаты поиска

Содержание 6EP4131-0GB00-0AY0

Отзывы:

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренды по названию

Популярные бренды