Siemens 6EP1437-3BA10 Скачать руководство пользователя страница 35

Страница: 35 / 58

Technical data

6.4 Closed-loop control

SITOP PSU8200 3ph
Manual, 11.2014, C98130-A7638-A1-2-7629

6.4

Closed-loop control

6EP3436-8SB00-0AY0

(24 V/20 A)

6EP1437-3BA10

(24 V/40 A)

Dyn. line regulation (Ue rated ±15 %), max.

1 %

Dyn. load regulation (Ia: 50/100/50%), Ua ± typ. 2 %

3 %

Load step regulation time 50 to 100 %, typ.

2 ms

Load step regulation time 100 to 50 %, typ.

2 ms

Regulation time / maximum

10 ms

6.5

Protection and monitoring

6EP3436-8SB00-0AY0 (24 V/20 A)

6EP1437-3BA10 (24 V / 40 A)

Output overvoltage protection

< 35 V

Current limitation, typ.

23 A

44 A

Property of the output/short-circuit

proof

Yes

Short-circuit protection

Optional constant current characteristic curve or latching shutdown

Continuous short-circuit current / rms

value / typical

•

Comment

23 A

Overload capability 150 % Ia rated up

to 5 s/min

44 A

Overload capability 150% Ia rated up to

5 s/min

Overload / short-circuit display

Yellow LED for "overload", red LED for

"latching shutdown"

Yellow LED for "overload", red LED for

"latching shutdown"

6.6

MTBF

6EP3436-8SB00-0AY0 (24 V/20 A)

6EP1437-3BA10 (24 V / 40 A)

Mean Time Between Failures

SN29500: >500000 hours at 40 °C,

rated load, 24-hour operation

SN29500: > 500,000 hours (typ.

700,000 hours) at 40° C, rated load,

24-hour operation

Содержание 6EP1437-3BA10



























































Результаты поиска

Содержание 6EP1437-3BA10

Отзывы:

Siemens 6EP1437-3BA10, Руководство пользователя, Страница: 35 / 58

Результаты поиска

Содержание 6EP1437-3BA10

Отзывы: