Siemens 6EP1437-3BA10 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 58

Siemens 6EP1437-3BA10 Скачать руководство пользователя страница 17

SITOP PSU8200 3ph
Manual, 11.2014, C98130-A7638-A1-2-7629

17

Mounting/removing

3

WARNING

Installing the device in a housing or a control cabinet
The SITOP PSU8200 3ph power supply is a built-in device. It must be installed in a housing

or control cabinet, to which only qualified personnel have access.

The device can be mounted in a control cabinet on standard mounting rails according to

EN 60715.

Mounting
To mount the device, position it with the mounting rail guide at the upper edge of the

standard mounting rail and press down to lock it into place. If this is too difficult, press slider

⑧

at the same time, as described under "Removal".

Removal
To remove, pull up the slider

⑧

using a screwdriver and disengage the device at the bottom

edge of the standard mounting rail. Then you can remove the device from the upper edge of

the standard mounting rail.

Figure 3-1

Mounting/removal (example 6EP3436-8SB00-0AY0)

«
...
15
16
17
18
19
...
»

Содержание 6EP1437-3BA10



























































Отзывы:

Нет отзывов