Siemens 3VA1 100 A Скачать руководство пользователя

Страница: 350 / 532

Accessories

4.8 Residual current devices

3VA molded case circuit breakers

350

Manual, 04/2015, A5E03603177010-02

Communications interface

The RCD-ETU connecting cable not only carries the trip command, but also acts as the

communications interface between the residual current device and the 3VA communication

system.
Precondition for interface functionality:

●

The 3VA2 molded case circuit breaker is equipped with a communication-capable,

electronic trip unit (ETU 5-series or 8-series).

●

The molded case circuit breaker is linked to the communication system via a COM060

communication module.

If the residual current device is linked to the communication system, the link can be used not

only to interrogate the device for important status, diagnostic, maintenance and identification

data, but also to transmit commands.
The residual current device is normally supplied with power by the main current paths. If the

molded case circuit breaker is switched off, this power supply is also disconnected (infeed at

top). In order to maintain the link to the communication system when the power supply from

the main current paths is disconnected, the residual current device is supplied with the

necessary power by the COM060 communication module.

Содержание 3VA1 100 A





















































































































































































































































































































































































































































































































































Результаты поиска

Содержание 3VA1 100 A

Отзывы:

Похожие инструкции для 3VA1 100 A

Бренды по названию

Популярные бренды

Siemens 3VA1 100 A, Руководство пользователя

Результаты поиска

Содержание 3VA1 100 A

Отзывы:

Похожие инструкции для 3VA1 100 A

Бренды по названию

Популярные бренды