manualshive.com logo in svg

Siemens 1PQ8, Инструкция по эксплуатации и установке

Поделиться
Скачать
Siemens 1PQ8 Скачать руководство пользователя страница 95

9.1.2

Measurement of the insulation resistance and polarization index in the context of 

maintenance work

Measuring the insulation resistance and polarization index (PI) provides information on the 

condition of the machine. It is therefore important to check the insulation resistance and the 

polarization index at the following times:     
● Before starting up a machine for the first time
● After an extended period in storage or downtime
● Within the scope of maintenance work
The following information is provided regarding the state of the winding insulation:
● Is the winding head insulation conductively contaminated?
● Has the winding insulation absorbed moisture?
As such, you can determine whether the machine needs commissioning or any necessary 

measures such as cleaning and/or drying the winding:
● Can the machine be put into operation?
● Must the windings be cleaned or dried?
Detailed information on testing and the limit values can be found here:
"Testing the insulation resistance and polarization index"  (Page 45) 

9.1.3

Inspections in the event of faults

Natural disasters or unusual operating conditions, such as overloading or short circuit, are 

faults that overload the machine electrically or mechanically.
Immediately perform an inspection after such faults.     

9.1.4

First inspection after installation or repair

Perform the following checks after approximately 500 operating hours or at the latest six 

months after commissioning:     

Table 9-1

Checks after assembly or repair 

Check

When the 

motor is 

running

At stand‐

still

The stated electrical characteristics are being observed.

X

 

The permissible bearing temperatures are not exceeded.

X

 

The smooth running characteristics and machine running noise have not 

deteriorated.

X

 

The motor foundation has no cracks and indentations. (*)

X

X

(*) You can perform these checks while the motor is running or at a standstill.

Maintenance

9.1 Inspection and maintenance

SIMOTICS TN Series N-compact  1LH8

Operating Instructions 06/2017

95

Содержание 1PQ8













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды