Siemens 1PQ8 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 140

Siemens 1PQ8 Скачать руководство пользователя страница 49

5.2.4

Removing the rotor shipping brace from machines with vertical type of

construction

NOTICE
Removing the rotor shipping brace in the horizontal position.
Dismantling the rotor shipping brace when the machine is in a horizontal position could

damage the bearings.
● Only remove the rotor shipping brace when the machine is in a vertical position.

NOTICE
Turning the motor over without rotor shipping brace
Failure to fit the rotor shipping brace can result in damage to the bearings while the machine

is being turned onto its side.
● Fix the rotor in place before you turn the machine into a horizontal position.

5.2.5

Removing anti-corrosion protection

Machined, bare metallic surfaces of the motor, such as the shaft end, fitted key, foot and flange

surfaces, are treated with an anti-corrosion agent.
1. Remove this layer of anti-corrosion agent from the mounting surfaces of the motor by wiping

it away with an absorbent cloth or paper sheet.

NOTICE
Damage to the machine surface
Using metal objects such as scrapers, spatulas, or plates to remove the anti-corrosion

protection could result in damage to the surfaces of the machine parts.

2. Then lightly oil the bare surfaces again.

Assembly

5.2 Lift the machine to where it will be installed, and position it

SIMOTICS TN Series N-compact 1LH8

Operating Instructions 06/2017

49

«
...
47
48
49
50
51
...
»

Содержание 1PQ8













































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды