manualshive.com logo in svg

Siemens 1PQ8, Инструкция по эксплуатации и установке

Поделиться
Скачать
Siemens 1PQ8 Скачать руководство пользователя страница 15

WARNING

Rotating parts     
Electric machines contain dangerous rotating parts.
Fatal or severe injuries and substantial material damage can occur if the covers are removed 

or if the machine is not handled, operated, or maintained properly.
● Only remove the covers using the methods described by these operating instructions.
● Operate the machine properly.
● Regularly and correctly maintain the machine.
● Secure free shaft extensions and other rotating part such as couplings and pulley belts 

so that they cannot be touched.

WARNING

Hot surfaces     
Electric machines have hot surfaces. Touching hot surfaces can result in severe burns.
● Allow the machine to cool before starting work on the machine.
● Only remove the covers using the methods described by these operating instructions.
● Operate the machine properly.

CAUTION

Hazardous substances     
Chemical substances required for the setup, operation and maintenance of machines can 

present a health risk.
Poisoning, skin damage, cauterization of the respiratory tract, and other health damage may 

result.
● Read the information in these operating instructions and the product information supplied 

by the manufacturer.

● Observe the relevant safety regulations and wear the personal protective equipment 

specified.

CAUTION

Flammable substances     
Chemical substances required for the setup, operation and maintenance of machines may 

be flammable.
Burns and other damage to health and material may result.
● Read the information in these operating instructions and the product information supplied 

by the manufacturer.

● Observe the relevant safety regulations and wear the personal protective equipment 

specified.

Safety information

2.4 Safe handling

SIMOTICS TN Series N-compact  1LH8

Operating Instructions 06/2017

15

Содержание 1PQ8













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды