manualshive.com logo in svg

Siemens 1PQ8, Инструкция по эксплуатации и установке

Поделиться
Скачать
Siemens 1PQ8 Скачать руководство пользователя страница 14

4. Ground and short-circuit.
5. Provide protection against adjacent live parts.
To energize the system, apply the measures in reverse order.

2.3

Qualified personnel

All work at the machine must be carried out by qualified personnel only. For the purpose of 

this documentation, qualified personnel is taken to mean people who fulfill the following 

requirements: 
● Through appropriate training and experience, they are able to recognize and avoid risks 

and potential dangers in their particular field of activity.

● They have been instructed to carry out work on the machine by the appropriate person 

responsible.

2.4

Safe handling

Workplace safety depends on the attentiveness, care, and common sense of the personnel 

who install, operate, and maintain the machine. In addition to the safety measures cited, as a 

matter of principle, the use of caution is necessary when you are near the machine. Always 

pay attention to your safety.
Also observe the following to prevent accidents:
● General safety regulations applicable in the country where the machine is deployed.
● Manufacturer-specific and application-specific regulations
● Special agreements made with the operator
● Separate safety instructions supplied with the machine
● Safety symbols and instructions on the machine and its packaging

WARNING

Live parts     
Electric machines contain live parts.
Fatal or severe injuries and substantial material damage can occur if the covers are removed 

or if the machine is not handled, operated, or maintained properly.
● Always observe the “five safety rules" (Page 13) when carrying out any work on the 

machine.

● Only remove the covers using the methods described by these operating instructions.
● Operate the machine properly.
● Regularly and professionally maintain the machine according to the instructions provided 

in Chapter "Maintenance".

Safety information
2.3 Qualified personnel

SIMOTICS TN Series N-compact  1LH8

14

Operating Instructions 06/2017

Содержание 1PQ8













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды