Siemens 1PH818 Скачать руководство пользователя страница 89

Страница: 89 / 198

4. During the test run, check and document the following:

– Check whether it is running smoothly.
– Document the voltage, current and power values. As far as possible, document the

corresponding values of the driven machine.

– If this is possible using the available measuring equipment, check the bearing and stator

winding temperatures until they have reached steady-state values.

– Check the machine for noise or vibrations on the bearings or bearing shields as it runs.

5. In case of uneven running or abnormal noise, switch off the machine. As the machine runs

down, identify the cause.
– If the mechanical operation improves immediately after the machine is switched off, then

the cause is magnetic or electrical.

– If the mechanical running does not improve immediately after switching the machine off,

then the cause is mechanical.

- Imbalance of the electrical machine or the driven machine

- The machine set has not been adequately aligned

- The machine is being operated at the system resonance point. System = motor, base

frame, foundation, ...

NOTICE
Serious damage to the machine
If the vibration values in operation are not maintained in accordance with DIN ISO

10816-3, then the machine can be mechanically destroyed.
● During operation, observe the vibration values in accordance with DIN ISO 10816‑3.

NOTICE
No-load operation without cantilever force
Never operate motors with cylindrical roller bearings in no-load operation without any

cantilever force Otherwise, this could damage the bearings.

7.7

Set values for monitoring the bearing temperature (optional)

Prior to commissioning

If the machine is equipped with bearing thermometers, set the temperature value for

disconnection on the monitoring equipment before the first machine run.

Table 7-1

Set values for monitoring the bearing temperatures before commissioning

Set value

Temperature

Alarm

115 °C

Shutting down

120 °C

Commissioning

7.7 Set values for monitoring the bearing temperature (optional)

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

Содержание 1PH818







































































































































































































Результаты поиска

Содержание 1PH818

Отзывы:

Бренды по названию

Популярные бренды

Siemens 1PH818, Инструкция по эксплуатации и установке

Результаты поиска

Содержание 1PH818

Отзывы:

Бренды по названию

Популярные бренды