Siemens 1PH818 Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 198

background image

7.5

Switching on

● See the operating instructions of the frequency converter for switching on.
● Before you switch on the motor, ensure that the parameters of the frequency converter

have been assigned correctly.

● Use appropriate commissioning tools, such as "Drive ES" or "STARTER".

NOTICE
Operation noise or abnormal noises
The motor can be damaged by improper handling during transport, storage or set up. If a

damaged motor is operated damage to the winding, bearings or, complete destruction of

the motor can be the result.
If the motor is not running smoothly or is emitting abnormal noises, de-energize it, and

determine the cause of the fault as the motor runs down.

Maximum speed
The maximum rotational speed n

max

is the highest permissible operating speed. The maximum

rotational speed is specified on the rating plate.

See also

Description (Page 21)

7.6

Test run

After installation or inspection, carry out a test run:
1. Switch on the cooling systems.
2. Start up the machine without a load. To do this, close the circuit breaker and do not switch

off prematurely. Check whether it is running smoothly.

Switching the machine off again while it is starting up and still running at slow speed should

be kept to a bare minimum, for example for checking the direction of rotation or for checking

in general.

Allow the machine to run down before switching it on again.

3. If it runs perfectly, connect a load.

Commissioning
7.6 Test run

SIMOTICS M-1PH8 1PH818., 1PH822.

88

Operating Instructions 07/2016

«
...
86
87
88
89
90
...
»

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1PH818

Бренд: VAR-SPE Страницы: 80

VLT OneGearDrive

Бренд: Danfoss Страницы: 44

VLT OneGearDrive

Бренд: Danfoss Страницы: 21

Бренд: Danfoss Страницы: 20

HO Union Pacific

Бренд: MTHTrains Страницы: 31

Бренд: Briggs & Stratton Страницы: 12

Бренд: BAFANG Страницы: 6

Бренд: Nakanishi Страницы: 2

Бренд: BMW Страницы: 41

Бренд: YS Страницы: 2

Бренд: Robin America Страницы: 32

Бренд: Robin America Страницы: 35

Бренд: Vetus Страницы: 80

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 3

Бренд: Mitsubishi Страницы: 155

Бренд: Mack Страницы: 43

RolloTube S-line DuoFern

Бренд: RADEMACHER Страницы: 2

Бренд: Zenith Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды