manualshive.com logo in svg

Siemens 1PH818, Инструкция по эксплуатации и установке

Поделиться
Скачать
Siemens 1PH818 Скачать руководство пользователя страница 84

7.1

Magnetic field when the brake is open

WARNING

Magnetic field when the holding brake is open 
If the motor is equipped with a holding brake, then the shaft extension is magnetized when 

the holding brake is open, i.e. if a voltage is connected to it.
Magnetic objects will then be suddenly attracted as a result of this magnetic field. This can 

result in death, severe injury or material damage.
● Working close to the shaft extension is only permissible in exceptional, justified cases. 

Clear access rules must be applied and complied with corresponding to magnetic fields 

at the workplace. Clearly mark the boundaries of the areas where standing is permitted. 

● People who need to use electronic or magnetic medical aids such as pacemakers, hearing 

aids, implants or similar devices, are at particularly high risk. Such persons must undergo 

an occupational health assessment.

● Observe the following measures.

Personal protective measures
● Ensure that you never wear or carry any of the following objects and that they are kept a 

safe distance from the machine:
– All kinds of magnetic metal parts such as, keys, glasses, tools, knives, scissors, tape 

measures, etc.

– Magnetic jewelry such as rings, chains, needles, watches, etc.
– Electronic devices and data carriers such as service cards, check cards, credit cards, 

calculators, cell phones, etc.

– Wallets or other iron-containing objects
– Electrically conductive foreign bodies

● Do not use any magnetic tools or lifting devices.
● Wear only occupational safety items without magnetic metal parts, e.g. occupational safety 

shoes with non-magnetic protective caps and soles.

● Keep your shoes and clothing free from chips and waste containing iron.
● Exercise caution when installing accessories. Ensure that no parts fall into the inside of the 

machine.

● Do not perform any cutting at the machine, e.g. drilling threaded holes. Any exceptions 

require written approval from the manufacturer.

See also

The five safety rules (Page 13)

Commissioning
7.1 Magnetic field when the brake is open

SIMOTICS M-1PH8  1PH818., 1PH822.

84

Operating Instructions 07/2016

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды