manualshive.com logo in svg

Siemens 1PH818, Инструкция по эксплуатации и установке

Поделиться
Скачать
Siemens 1PH818 Скачать руководство пользователя страница 75

6.4

Auxiliary circuits

6.4.1

Selecting cables

Take the following criteria into account when selecting the connecting cables for the auxiliary 

circuits:
● Rated current
● Rated voltage
● System-dependent conditions, such as ambient temperature, routing type, cable cross-

section as defined by required length of cable, etc.

● Requirements according to IEC/EN 60204‑1 

6.4.2

Connecting an external fan

Preconditions  
● Only use cables that comply with the relevant installation regulations regarding voltage, 

current, insulation material, and load-carrying capacity.

● Before connecting the device, make sure that the line voltage matches the device voltage.
● Check whether the data on the fan rating plate matches the connection data.
● Cable glands are not included in the scope of supply. Close unused cable entries, 

otherwise, the degree of protection is not maintained.

● The line voltage corresponds to the quality attributes laid down in DIN EN 50160 and the 

defined standard voltages laid down in DIN IEC 60038.

Procedure
1. Open the terminal box of the external fan and route the cables into it. The cables are not 

included in the scope of supply.

2. Connect the protective conductor (PE).
3. Connect the other cables to the relevant terminals, refer to the connection diagram in the 

terminal box.

Connection cables must not be subject to excessive tensile stress.

Note
For fans equipped with EC motor, the fan motor starts with a delay after the line voltage is 

connected.

Electrical connection

6.4 Auxiliary circuits

SIMOTICS M-1PH8  1PH818., 1PH822.

Operating Instructions 07/2016

75

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды