Siemens 1PH818 Скачать руководство пользователя страница 60

Страница: 60 / 198

5.2.8

Putting the machine down

Requirements

The following preconditions must be satisfied before setting down the machine at the

installation location:
● The mating faces must be clean.
● The anti-corrosion protection paint has been removed from the mating faces, such as the

machine mounting feet, flange, ...

● There is no condensation present within the machine.

Setting down the machine

● Set down the machine slowly and carefully at the installation location to avoid any impact.

5.2.9

Roughly aligning the machine

Requirement

The transmission element such as a coupling half has already been pulled on.

Roughly aligning the machine

● For horizontal positioning, push the motor sideways across the foundation. When doing so,

ensure that the axial position is maintained.

5.3

Installing the machine

WARNING

Inappropriate fastening material
If screws of an incorrect property class have been selected or if they have been fastened to

an incorrect tightening torque, they may break or become loose. This will cause the machine

to move, which could damage the bearings. The rotor could smash into the machine enclosure

and machine parts could be flung out of place. This can result in death, serious injury or

material damage.
● Comply with the required property classes for screwed connections.
● Tighten the screwed connections to the specified tightening torques.

Mounting
5.3 Installing the machine

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

Содержание 1PH818







































































































































































































Результаты поиска

Содержание 1PH818

Отзывы:

Бренды по названию

Популярные бренды

Siemens 1PH818, Инструкция по эксплуатации и установке

Результаты поиска

Содержание 1PH818

Отзывы:

Бренды по названию

Популярные бренды