Siemens 1PH818 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 198

background image

5.2.3

Removing anti-corrosion protection

Machined, bright surfaces of machine parts and small components such as screws, bolts,

wedges, feather keys and dowel pins, are treated with an anti-corrosion agent.
Carefully remove the anti-corrosion agent just before starting the installation work.

Bright surfaces on machine parts

● Use petroleum, petroleum ether, or a similar solvent or detergent to remove the anti-

corrosion coating from the machined surfaces of machine parts and from small components.

NOTICE
Paintwork damage
If painted surfaces come into contact with the detergent or solvent, the paintwork can be

damaged.

● Use a suitable solvent to soften thick layers of anti-corrosion agent. Then push the softened

layers off using a piece of hardwood approximately 10 x 10 x 1 cm. Do not sand the

protective coating down or scrape it off.

NOTICE
Damage to the machine surface
If you use metal objects such as scrapers, spatulas, or plates to remove the anti-corrosion

protection, this could result in damage to the surfaces of the machine parts.

● Lightly oil the depreserved surfaces.

Mounting
5.2 Lift the machine to where it will be mounted and position it

SIMOTICS M-1PH8 1PH818., 1PH822.

54

Operating Instructions 07/2016

«
...
52
53
54
55
56
...
»

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1PH818

Бренд: GAPOSA Страницы: 2

Бренд: V2 Страницы: 17

Бренд: Toyama Страницы: 44

Бренд: Stark Страницы: 14

Бренд: Detroit Diesel Страницы: 135

Бренд: Hino Motors Страницы: 216

Бренд: Hino Страницы: 278

Бренд: O.S. engine Страницы: 18

Бренд: Golden Eagle Страницы: 11

Бренд: DLE Страницы: 4

Бренд: Mitsubishi Heavy Industries Страницы: 65

Бренд: Mitsubishi Heavy Industries Страницы: 78

Бренд: Desert Aircraft Страницы: 9

Бренд: FAAC Страницы: 104

Бренд: E-FLITE Страницы: 3

Power 25 Brushless Outrunner

Бренд: E-FLITE Страницы: 4

Бренд: Ford Страницы: 91

X30 125cc RL - TaG

Бренд: IAME Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды