Siemens 1PH818 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 198

background image

Mounting

5

When carrying out any work on the machine, observe the general safety instructions

(Page 13) and the specifications contained in EN 50110‑1 regarding safe operation of electrical

equipment.

Note
Loss of conformity with European directives
In the delivery state, the machine corresponds to the requirements of the European directives.

Unauthorized changes or modifications to the machine lead to the loss of conformity with

European directives and the loss of warranty.

5.1

Preparing for installation

5.1.1

Requirements for installation

The following requirements must be satisfied prior to starting installation work:
● Staff have access to the operating and installation instructions.
● The machine is unpacked and ready for mounting at the installation location.

Note
Measure the insulation resistance of the winding before starting installation work
Wherever possible, measure the insulation resistance of the winding before starting

installation work. If the insulation resistance lies below the specified value, take appropriate

remedial measures. These remedial measures may necessitate the machine being

removed again and transported.

NOTICE
High temperatures
The motor components get very hot during operation. High temperatures can damage

mounting parts such as the cable insulation.
● Temperature-sensitive parts such as normal cables or electronic components must not

rest against or be attached to mounted machine parts.

● Only use heat-resistant mounting parts. The connecting cables and cable entries must be

suitable for the ambient temperature.

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

49

«
...
47
48
49
50
51
...
»

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1PH818

Бренд: Selve Страницы: 132

ZA top SM210.60

Бренд: ZIEHL-ABEGG Страницы: 96

Бренд: Brother Страницы: 76

Бренд: Brother Страницы: 112

Бренд: Brother Страницы: 22

Бренд: NetGain Motors Страницы: 34

Бренд: Honda Страницы: 5

Бренд: Honda Страницы: 16

Бренд: Ingersoll-Rand Страницы: 42

Бренд: KEM Страницы: 61

Бренд: M.T.H. Страницы: 47

Бренд: O.S. engine Страницы: 38

Бренд: SKY Engines Страницы: 26

Бренд: Mitsubishi Страницы: 90

Бренд: Mitsubishi Страницы: 105

Бренд: Yanmar Страницы: 42

Char-Lynn S Series

Бренд: Eaton Страницы: 13

Бренд: Detroit Diesel Страницы: 442

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды