manualshive.com logo in svg

Siemens 1PH818, Инструкция по эксплуатации и установке

Поделиться
Скачать
Siemens 1PH818 Скачать руководство пользователя страница 41

4.13.5

Transporting the machine set

WARNING

Falling down of the machine
The lifting lugs on the machine are designed only for the weight of the machine. If a machine 

set is lifted and transported on a single machine, this can lead to mechanical failure of the 

lifting lug. The machine or machine set may fall. This can result in death, serious injury or 

material damage.
● Do not lift machine sets by attaching lifting tackle to the individual machines.
● Use only the equipment provided, e.g. the openings or lugs on the base plates, for 

transporting machine sets. Note the maximum capacity of the lifting lug.

Note
Place the machine in a secure and raised position
In order to obtain easy and safe access to the underside of the machine, place it in a secure 

and raised position.

DANGER

Standing under suspended loads
If the lifting gear or load handling attachments were to fail, the machine could fall. This can 

result in death, serious injury or material damage. 
Never remain under or in the immediate vicinity of the machine when it is raised.

4.13.6

Storage

You can store the machine for up to two years in dry, dust-free and vibration-free rooms without 

reducing the specified storage time.

NOTICE
Seizure damage to bearings  
If the motor is stored incorrectly, bearing damage can occur at standstill, e.g. brinelling, as a 

result of vibration or shock. 
Read the following storage instructions. 

Preparation

● Fit the rotor shipping brace.
● Apply a preserving agent, for example to external components such as shaft ends, if this 

has not already been applied in the factory.

Preparations for use

4.13 Transport and storage

SIMOTICS M-1PH8  1PH818., 1PH822.

Operating Instructions 07/2016

41

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды