Siemens 1PH818 Скачать руководство пользователя страница 16

Страница: 16 / 198

WARNING

Noise emissions
During operation, the machine's noise emission levels can exceed those permitted at the

workplace, which can cause hearing damage.
Take steps to reduce noise, such as introducing covers and protective insulation or adopting

hearing protection measures, so that the machine can be operated safely within your system.

2.5

Working on machines with permanent magnets

On machines with permanent magnets, the magnetic field is guided in an assembled state in

the magnetic circuit of the machine. This means that no magnetic fields, which may be to your

health, are detectable outside the machine.

WARNING

Strong magnetic field when the machine is open
A strong magnetic field is always present inside the machine. If the housing is open, e.g.

when maintenance openings are open or when working inside the machine, magnetic objects

can be suddenly attracted by this magnetic field. This can result in death, severe injury or

material damage.
Working in the vicinity of the rotor is only permitted in exceptional circumstances.

Unambiguous access rules must be established in accordance with the magnetic fields

prevailing in the workplace. Clearly mark the boundaries of the areas where standing is

permitted.
People who need to use electronic or magnetic medical aids such as pacemakers, hearing

aids, implants or similar devices, are at particularly high risk. Such persons must undergo an

industrial medicine assessment.
Observe the following measures.

Safety information
2.5 Working on machines with permanent magnets

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

Содержание 1PH818







































































































































































































Результаты поиска

Содержание 1PH818

Отзывы:

Бренды по названию

Популярные бренды

Siemens 1PH818, Инструкция по эксплуатации и установке

Результаты поиска

Содержание 1PH818

Отзывы:

Бренды по названию

Популярные бренды