Siemens 1PH818 Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 198

background image

NOTICE
Applying force
If excessive forces are present, this can damage the fan impeller.

● Use a suitable cloth or brush to clean the external fan, ensuring that moisture does not

enter the motor.

● Once the voltage has been disconnected on all poles, wait for five minutes before touching

the device.

● Never open the external cooling unit during operation.
● Never loosen any fixing screws for the external cooling unit during operation.

Changing the filter mat of the external fan (option)

Check the state of the filter mat regularly depending on the prevailing conditions. Change it if

it is dirty.

CAUTION

Changing the filter only when the fan is stationary
When the mesh is removed, the degree of protection is no longer guaranteed. There is a risk

of injury. Only change the filter when the fan is stationary.

1. Unscrew the fan guard and remove the old filter mat.
2. Insert the new filter mats and screw the fan guard back into position.
You can order the filter mat as a spare part.
● Spare parts, external fan (Page 123)
● Spare parts kits (Page 119)
● Ordering spare parts via the Internet (Page 120)

9.2.6.8

Maintaining terminal boxes

Requirement

The machine is de-energized.

Checking the terminal box

● Terminal boxes must be regularly checked for tightness, undamaged insulation, and tight

terminal connections.

● If dust or humidity have infiltrated the terminal box, this should be cleaned and dried

(particularly the insulators).

Check all the seals and sealing surfaces and address the cause of the leakiness.

Maintenance

9.2 Inspection and maintenance

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

113

«
...
111
112
113
114
115
...
»

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1PH818

EC FSE 400 - SERVICE 2002 & 2003

Бренд: GAS GAS Страницы: 74

PRESTIGE PS2.60FA

Бренд: CAB Страницы: 16

Бренд: Navistar Страницы: 120

Бренд: 3W Страницы: 19

LYCOMING 200-6XL Series

Бренд: E-MAG Страницы: 30

Бренд: Exalto Страницы: 28

AG2210-LP Series

Бренд: Beckhoff Страницы: 35

Бренд: Black Bruin Страницы: 70

Бренд: Andersen Страницы: 20

Бренд: DUROMAX Страницы: 70

Бренд: Leadshine Technology Страницы: 11

Бренд: Lycomin Страницы: 171

Бренд: O.S. engine Страницы: 17

Бренд: O.S. engine Страницы: 20

Бренд: DLE Страницы: 4

Бренд: DANA Страницы: 3

Бренд: LONCIN Страницы: 22

ANORAD LZ Series

Бренд: Rockwell Automation Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды